ruthex M2 Threaded Inserts - 70 Pieces RX-M2x4 Brass Heat Set Insert for Plastic Parts - Metric knurled Nuts - Insert by Heat into 3D Printing Components

Let me just say this—if you’re printing enclosures or mounts and not using threaded inserts like these… you’re playing life on hard mode.I’ve burned through enough 3D prints to know that tapping straight into PLA or PETG is like trusting a paper towel in a hurricane. That’s where these ruthex M3 inserts come in and save the day like some kind of tiny, brass-threaded Avengers.These things heat-set like butter. No deformation, no bulging, no “oops, pushed too far” drama. The knurling bites in just right, and they seat clean at the recommended temps. I used a Weller iron with a blunt tip, hovered around 210–220°C, and every single one went in textbook perfect. No cracking, no misalignment.They don’t back out when you unscrew either. I’ve tested that plenty—over-tightening, removing and re-seating a half-dozen times—and they still hold strong like it’s their first day on the job.And the RX series? 👌 These aren’t your dollar-store “sorta fits” inserts. These are precision made. Consistent sizing, clean threads, and they ship in a plastic box that doesn’t explode open like it’s trying to test your patience.What I Like:Insertions are clean, controlled, and oddly satisfyingNo burrs or malformed pieces—every single one was usableThreads hold torque like a champ, no pull-outsruthex isn’t playing around—these are real-deal engineered, not sketchy mass-stamped junkWhat Could Be Better:Honestly? Include a small tool or press-fit guide for new users maybe. That’s all I got.Oh, and maybe a reminder that yes, they are hot after heat-setting (ask my thumb)TL;DR:If you’re printing anything that needs to be unscrewed more than once, stop relying on melted plastic holes and upgrade your builds. These ruthex M3 inserts are rock solid, heat-set clean, and make your prints look and feel pro.Your future self (and your screwdriver) will thank you.

I purchased these inserts along with a heat gun also found on Amazon with additional tips used for soldering and 3D Printing. I recommend drilling a pre hole first to eliminate overheating the plastic and then simply insert the specific brass tip into the insert and set temperature to about 300ºF. If you flare the pre-hole after drilling and before inserting the insert there will be no noticeable melted plastic around the finished insert. I always set the insert below flush and use a razor blade to remove any residue around the depressed insert.

I used these in some 3d prints and they worked great and held together. Their sizing is also accurate, as I double checked with some digital calipers. I was really bored and even counted how many came in the bag. The bag said 100, and I counted exactly 100. Not bad.

These inserts are fabulous. I tried some other "cheap" ones and gave up. I bought these on whim, and was so satisfied with the ease of insertion and mechanical grip. These insert are definitively a great value for the money.

These are the best that I've tried. The angled serrations bite hard in the plastic and are very hard to pull out.I use a soldering iron to sink these into plastics and am very impressed by how well they work.

These were exactly what I needed for a 3d printed violin I made! They're made well and can hold a great amount of pressure! The chin rest and the neck (both grey pieces) are being held with these. My only real problem with the product is the fact that it didn't come with the solder tip needed to melt these in and I had to buy it separately. It seems like something so simple should be added with this.

I usually keep a bunch of these on hand to add M3 threading to heavier duty 3D prints. They're consistently machined within very good tolerances, and there haven't been any surprises. Work well with PLA, PETG, and ASA plastics that I've used.

These were better than the general ones I have seen.They do have sharper edges and the haven’t slipped to other I have with PLA and PETG 3d printsDefinitely will repurchase once I have to.