ERYONE Silk Dual Color PLA Filament 1.75mm, Co-Extrusion PLA Silk Filament for 3D Printer, Bicolor Silk Two-Tone PLA, +/-0.03mm, 1KG Spool, Silk Black Purple

Printed really nicely once dialled in, great colour and really well rolled so that the colour mostly stays on one side. Looks great on the details of the Ghostship bench, and super smooth and shiny on the Bulbasaur model. Minimal stringing.

Minimal stringy, prints well in A1 mini using the spool's temperature recommendations, but also prints well on default settings. Silks really show up seams and scarf joints (don't use with silk), so position these well before printing. Also got the bronze super silk from ERYONE and it has been great.

Good stuff ...cool effect

First things first... When you look at the attached images - bear in mind that the 'artifacts' seen on the print are my fault, not the fault of the filament. I forgot that given the size of the upright parts, that if left unsupported, they would start wobbling around the higher up i got 🤦‍♂️🤦‍♂️On to the review...The ERYONE SILK GOLD PLA is a lovely colour and really does have a lovely shine to it.It's lovely to print with, and worked straight out of the box on my standard PLA settingsThe temperatures used were 195 for the hotend, 65 for the bed.The only real couple of negative comment i have on this filament is to do with the tollerance on the diameter.It is advertised on amazon as 1.75mm +-0.02mm, but on the spool, it is labelled as +-0.05 - I'm not sure which is incorrect, however my personal experience is the below:I measured the diameter at various points along the spool throughout the few prints i have used this filament for so far, and the diameter seems to actually vary from 1.70-1.85, giving anywhere between -0.05 and +0.10mm away from the 1.75 it is supposed to be.The 1.70 and 1.85 measurements did seem to be one-off variations however, and the majority of measurements i took were within +-0.03 of 1.75mm which i would consider more than acceptable.This is definitely going to become my 'go to' for gold filament.I have also used their red PLA and black PETG in the past, and have never had any issue with either of those.Great job ERYONE, i'll be back for some more when i get low! :)

Well packaged and prints fantasticly. The colours look really good and the prints look awesome. Would buy again and would try other colours.

The media could not be loaded. This is the coolest filament yet, got the red /blue /green one. Printing on Bambu A1 Mini with AMS, setting on Generic PLA Silk worked great. Very cleanly wrapped, no tangles. So happy I got this!!

This is an excellent filament that provides brilliant print quality and shiny finish.I was initially impressed with how easy it was changing to this filament.I changed from a different brand of pla to this silk pla quickly and with no difficulties.The first print I did was the low poly vase model.Each side of the vase is very linear with good layer adhesion and only 1 artefact, that was due to the bed level being slightly off.For a first print this was very impressive, and the 'silk' nature of the filament really shines when under the light.The second print I did was the Koch Snowflake vase. This time with the bed levelled properly, the part came out flawless. The surface finish is very even and the model is strong, and would not snap when dropped on a hard surface.Finally the third test print I did was part of an RC plane fuselage that I designed.This had fairly thick walls, and unlike the other 2 models, was one continuous parallel line. This really showed how little artefacts appeared on the print.I also found that this made the silk really pop, as unlike with the snowflake vase, there was only 1 direction for the light to reflect off and so really gave the appearance of a metal-like material.Overall this is a brilliant filament, that benefits from the silk to give a metal-like look, with a good representation of the copper colour that it is based off.

Great colour, no adhesive issues. However not sure if the silk is expanding as I found the nozzle hit the print the around the same hight.. breaking the print, 6 fails. I did the usual checks and calibrations .. same issue... Yet print works fine on 5 other random pla filaments with same slicer setting including another silk tricolour.

Beautiful output especially at slower speeds. On a K1C, I got this at at 100mm/s speed. Trying another one at 75mm/s and it seems to be really bringing out the colors and shine. Nozzle temp is 215 for first layer, 205 for the rest. Started with bed temp at 55 degrees, but had trouble removing the brims afterwards. Trying a print at 45 degree bed temp, and if that also results in the brims getting stuck to the bed, will try not applying glue to the smooth PEI plate or may eliminate the brims altogether

Ürün güzel ancak fazla pahalı

Good looking filament , printed perfectly using the Bambu Silk Pla settings in Bambu Studio. Would highly recommend this filament to anyone who likes theese colors. Keep in mind bigger prints look way better than small prints. 5/5 would buy again

Très facile à imprimer et les couleurs sont magnifiques.

Great filament, prints look cool. I use it with a dehumidifier, probably that also helps of course